1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.
  2. Greetings Guest!!

    In order to combat SPAM on the forums, all users are required to have a minimum of 2 posts before they can submit links in any post or thread.

    Dismiss Notice

Small forge and anvil under a stone table?

Discussion in 'UO Homes and Castles' started by DJAd, Mar 1, 2014.

  1. DJAd

    DJAd Stratics Legend
    Stratics Veteran

    Joined:
    Aug 17, 2007
    Messages:
    7,936
    Likes Received:
    3,588
    Is it possible to have a small forge, anvil and possibly a small soul forge placed under a stone table and them still be usable?
     
  2. Tazar

    Tazar Guest

    If you can get them to place, then they would be usable. I'd try placing goza mats and raise them up until you can place the forge/anvil under them. The place the table on top of the mats. Lower one mat 2 notches to "break" the table then chop out the mats and lower the table into place. I *think* it will work.
     
  3. LowdownandShifty

    LowdownandShifty Journeyman

    Joined:
    Nov 19, 2013
    Messages:
    177
    Likes Received:
    49
    If you get this to work, please post a pic. I'd love to see it
     
  4. DJAd

    DJAd Stratics Legend
    Stratics Veteran

    Joined:
    Aug 17, 2007
    Messages:
    7,936
    Likes Received:
    3,588
    Yeah i'm going to give it a try tonight. I'm a bit of a deco rookie so wish me luck!
     
  5. Lady Michelle

    Lady Michelle Sprite Full SP
    Stratics Veteran The DarkOutlaws, TDO

    Joined:
    May 12, 2008
    Messages:
    2,451
    Likes Received:
    1,113
    Unless something was changed since Ive done this you should be able to lock the small forge and anvil down to raise or lower them with the house tool.
    I would raise the forge and anvil as high as I can see if I can place the stone table under them then lower them under it.
     
    Loren likes this.
  6. DJAd

    DJAd Stratics Legend
    Stratics Veteran

    Joined:
    Aug 17, 2007
    Messages:
    7,936
    Likes Received:
    3,588
    When I place the anvil and forge (deeded ones) it won't let me higher or lower them with the deco tool. From other peoples replies I think I need to place them on gorzas then raise these.
     
  7. Lady Michelle

    Lady Michelle Sprite Full SP
    Stratics Veteran The DarkOutlaws, TDO

    Joined:
    May 12, 2008
    Messages:
    2,451
    Likes Received:
    1,113
    I wasn't able to lock them down, but I could lower and raise them with the house tool.
    That is weird you can't raise or lower them and I can.
    making sure its a sm forge or lg forge? I used sm forge
    kinda house you have ?
     
  8. DJAd

    DJAd Stratics Legend
    Stratics Veteran

    Joined:
    Aug 17, 2007
    Messages:
    7,936
    Likes Received:
    3,588
    My bad, it does work! I re-deeded them and placed the forge and anvil again and it let me raise or lower them using the tool!

    I then raised both the forge and anvil up as high as it would allow me. I then placed the table and lowered them back down.

    Here is the end result (not quite the look I was hoping for!)

    [​IMG]
     
  9. Lady Michelle

    Lady Michelle Sprite Full SP
    Stratics Veteran The DarkOutlaws, TDO

    Joined:
    May 12, 2008
    Messages:
    2,451
    Likes Received:
    1,113
    Least you know it can be done.
    This is what I would of done....
    I would of placed gozas down
    I would of placed the anvil same place you have it ( you know if you use the colored wood you are able to use tokuno dyes on the anvil and forges not sure about plant dyes haven't tried it yet.)
    I'd raise the anvil as high as it goes. Then place the sm forge under the anvil raise the forge up as high as it goes.
    Then I would raise the gozas up 3 times each place the table on them.
    lower the anvil then the forge hiding the anvil inside the forge. then if it looks ok I would ax the goza matts